Danuser 9000 Postmaster/SlabBlaster Bedienungsanleitung

Si no entiende ingles, se prefiere que busque a alguien que interprete las instrucciones para usted. Owner: Date Purchased: Model #:

10STEP 13: Start the vehicle. Running at full throttle, engage the auxiliary hydraulics. Note the direction of the chain rotation (visible fro

11After the post is in position, the second person must move away from the Postmaster and vehicle.OperationPostmasterSTEP 17: After setting the flow

12STEP 4: After the second person has cleared the area, continue lowering the Postmaster onto the post approximately 24 inches. Gauge this measur

13STEP 2: Set the Grapple down in front of the Postmaster, aligning the square tubes of the Grapple with the square tubes of the Postmaster (one o

14Picking up a post from the ground may require a few tries to get it perfect. We recommend attaching a 24 inch length of deck chain to the hook prov

15STEP 11: Lower the Postmaster onto the post approximately 24 inches. Reposition the vehicle using the guide chain as a plum line.STEP 12: Tu

16STEP 4: Route the control portion of the wiring harness along the loader arm of the vehicle and into the cab, and secure the wiring with zip-tie

17Removal &StorageSTEP 3: The Slab Blaster can now be activated by turning the auxiliary hydraulics to the forward position.Before storage, th

18 a) Flow control setting too low Increase flow control setting. b) Fittings or connections Replace with proper fittings. are too small

CHECK FOR CLEAN HYDRAULIC OILThe majority of all hydraulic component failures are caused by contamination of the hydraulic oil. At all times, keep di

Dear Owner/Operator,Thank you for purchasing this Danuser Postmaster/Slab Blaster. We appreciate your business.Your safety as an operator of our prod

20ServiceSTEP 1: Remove the safety catch pin from the top of the frame. Insert a hook into the chain links welded to the top of the hammer, and l

21STEP 8: Position the new drive chain around the frame and sprockets, and install the pick- up link. Drive pins through the pick-up link and chai

22Service(continued)STEP 5: With the Postmaster in a horizontal position, remove the head assembly.STEP 6: If you are changing the collar only, then

23STEP 3: Raise the Postmaster in the air, and tilt it forward 90°. Watch for any obstructions or pinching of hydraulic hoses.STEP 4: Shut off t

24STEP 6: Start the vehicle, and slowly tilt the Slab Blaster back to a vertical position.STEP 7: Shut off the vehicle, and disconnect the hydraulic

25Drive AssemblyParts1 REF. NO. PART NO. DESCRIPTION QTY. 1 11150 Bushing (includes 3 Capscrews and 1 Key) 2 2 11151 Double Tooth Spro

26= Safety Sign LocationParts12346789101112131415165174193231822421204

* To convert from a Slab Blaster to a Postmaster, purchase items 1 through 9.** To convert from a Postmaster to a Slab Blaster, purchase item 10. RE

28 REF. NO. PART NO. DESCRIPTION QTY.  1 11168 HoseAssembly1/2”x30” 1  2 11169 HoseAssembly1/2”x24” 1 3 11214 90° Elbow 1

REF. NO. PART NO. DESCRIPTION QTY.  1 11168 HoseAssembly1/2”x30” 1  2 11169 HoseAssembly1/2x24” 1 3 11214 90° Elbow 1

Improper operation of this Postmaster/Slab Blaster can cause serious personal injury or death. Operation of this Postmaster/Slab Blaster should only

30GrappleParts34206789111101213141516195172118226272829302223242556421

31 REF. NO. PART NO. DESCRIPTION QTY. 1 11174 5/8”UNCLockNut 2 2 11175 5/8”FlatWasher 4 3 11176 Chain Guard 1 4 11177 Spann

32 REF. NO. PART NO. DESCRIPTION QTY. 1 11214 90° Elbow 1 2 11173 Hydraulic Motor 1 3 11219 90° Elbow 1 4 11220 Cylinder 1 5

33Decals &Safety SignsPART NO. DIG17Location: Unit, Rear ShelfModel Number & Serial NumberLocation: Unit, Bottom RightPART NO. DIG5Location:

DANUSERLIMITED WARRANTYDanuserMachineCompany,Inc.(“Danuser”)warrantsitsproducts,undernormaluseandmaintenance,tobefreefromdefectsinm

4Working with unfamiliar equipment can lead to careless injuries. Read and understand this manual and the manual for your vehicle before assembling,

• Consult local utility companies to make certain there are no buried gas lines, electrical cables, etc., in the work area before beginning operat

6Specifications• Round, square, or H-beam heads available for wood or steel posts, preventing post mushroom. T-post adapter and custom heads up

Filtration Requirements:• A filter of, at least, 25 micron filtration is required. A filter capable of 10 micron filtration is preferred. The ma

8Prepare the VehicleRead and understand the manual for your vehicle before assembling or installing the Postmaster/Slab Blaster. The vehicle must be

9STEP 7: Ensure the safety catch is in place. The safety catch prevents the hammer from sliding out of the Postmaster/Slab Blaster.STEP 8: Rai